大家在查： kerosene oil 超级周期接受询问机织布打酒萨尔曼光辉耀目 PhDmedicalgeneticist geomagnetic storm 推磨

Tailstock

美 ['teɪlˌstɒk]英 ['teɪlstɒk]

na.【机】尾座[架]；顶针[尖]座
网络尾架；护罩尾托；液压尾座

复数：tailstocks

Tailstock

Tailstock

英-汉英-英网络释义

Tailstock

na.

1.【机】尾座[架];顶针[尖]座

1

The largest part of the lathe is called the bed on which the headstock and the tailstock are fastened at opposite ends .

车床的最大的零件称床身，车头和尾架被紧固在相反末端的床身。

2

closer to go off work, should be cleaning and wipe test bed , and will the tailstock slip board box and withdrew to the right side, the bed .

临近下班，应清扫和擦试车床，并将尾座和溜板箱退到床身最右端。

4

If I understand your problem correctly , the first thing you have to check is the tailstock alignment with the headstock .

假如我正确地理解你的问题的话，你必须检查的第一件事是主轴与尾座的基准。

5

The basic components of the most common lathe (engine lathe ) are the bed , headstock, tailstock, and carriage .

最普遍的车床（普通车床）的基本组成部分包括：床身、主轴箱、尾架、拖板箱。

6

Model SPK36B series NC rotary tailstock is one of the accessories for the NC rotary table .

系列数控回转尾座是数控回转工作台配套附件。

8

The basic components of the must common lathe are the bed , headstock, tailstock, and carriage .

基本组成部分，必须共同车床，是在床上，头，尾，和运输。

9

The others end of the workpiece is supported by the tailstock .

工件的另外一端由尾架支撑。

10

The middle group of castings are the parts for the Gingery dividing head and tailstock .

铸件中的小组是为金格里分度头和尾架的部分。

11

On the back of the tailstock is a third thumbscrew that locks the tailstock in place on the dovetailed ways .

在背部的尾架是第三 thumbscrew 认为，锁尾架在地方上配合的方式。

12

the horizontal bed is the foundation member which supports the headstock , tailstock , and carriage.

卧式床身是基础构件，用来支承床头箱、尾座和拖板。

13

Tailstock . The tailstock assembly consists basically of three parts , its lower base , an intermediate part, and the quill .

尾架总成基本包括三部分，底座、尾架体和套筒轴。

14

The four guide way design allows collision-free traverse movement of the tailstock .

四根导轨设计避免了尾座来回移动时的碰撞。

15

All of the principal units of the lathe amounted on a bed having ways along which the carriage and tailstock travel.

车床的主要部件都装在具有导轨的床身上，刀架与尾架可沿着该导轨滑动。

16

The easiest solution is to check the alignment of the tailstock and the . . .

最容易解决的是尾座的基准，而且最坏的问题是主轴。

17

18

The drilling tool is held in the tailstock , and the latter is then fed against the workpiece .

钻孔刀具安装在尾架上，然后对着工件进给。

19

The main component of the lathe : Spindle Box, Tool, Tailstock , feed me, and the crate slipped bed .

车床的主要组成部分有：主轴箱、刀架、尾座、进给箱、溜板箱和床身。

20

then the tailstock center is shifted a distance S in the direction normal to the lathe axis .

然后将尾架顶尖朝垂直于车床主轴方向移动一距离 S 。

21

The hole you see is the sprue hole for the tailstock , the pulley 's sprue is not visible in the picture .

这个洞你看到的是为尾座浇道洞，滑轮的浇口是不可见图片。

22

Tailstock job first and special air bearing design, Shift Light labor-saving .

工作头及尾座特殊空气轴承设计、移位轻便省力。

23

On the upper part of the bed there are special ways upon which the carriage and the tailstock slide .

在床身的上部有支架和尾架滑板的特别结构。

24

The headstock, the tailstock and the carriage are all on the lathe bed .

主轴箱、尾架和托板都是安装在床身上的。

25

Both chuck and tailstock are supplied with hydraulic or manual or peneumatic type .

这两个夹头，液压尾座供应或手动或 peneumatic 类型。

26

Taper bore of tailstock barrel No.

尾座套筒锥孔锥度。

27

Cone of tailstock quill bore MT No.

尾架套筒孔莫式锥度。

28

Taper of Hole in Tailstock No.

尾座套筒锥孔。

29

But the entire tailstock 's curve for the human the quite capable feeling , most important is returns very much coordinated .

而整个车尾的曲线给人比较干练的感觉，最重要的就是回归得很协调。

30

Design of Special Boring Machine for Finish-machining Tailstock Hole of the Lathe

车床尾座体孔精镗专机的设计

热词推荐

大家在看