大家在查： designable galet Senso 一十五 couture clothing Xoom—— 煽动家一旦退化 amnesiacs 文学革命

顶出

adj.ejection
n.knockouts; kick-out
v.eject
网络Eject; ejector; push-out

顶出

英-汉网络释义

顶出

Eject

模具术语 - spaceboy77的日志 - 网易博客 ... Mould Unloading 开模 Eject 顶出 Mould Clamping 锁模 ...

ejector

机械手英文专业词汇_百度文库 ... Ejector valve 顶针阀 Ejector 顶出,脱模 Electomagnetic valve cover 电磁阀盖板 ...

push-out

pull... ... push out 推出去 push-out 顶出 They managed to pull in the tractor inside the shed. 他们设法把拖拉机拉进棚里。 ...

knockout

基因可以通过顶出(Knockout)而删除或者超量表达(Overexpression)而增加。在逆向法中采用了基因工程技术，通过分析改变特 …

Top out

苏净安泰AIRTECH BSC-1300 ⅡA2生物安全柜... ... 排风方向 Air Direction 顶出/ Top out （100级 Class 100 ...

Ejector Pin

模具日本语 - dwxydq的日志 - 网易博客 ... Design 设计 Ejector Pin 顶出 Design Drawing 设计图 ...

kicker

英汉日模具用语集——i～k-刘建平-信息化博客 ... keyway milling mahcine 键槽铣床 kicker 顶出 kil 工具箱 ...

例句：

The choice of runner section is also influenced by the question whether positive ejection of the runner system is possible .

流道截面的选择也受到流道系统的顶出是否实际可行的影响。

Since the cut blank will be retained in the die block by friction , some means of ejecting on the ram upstroke must be provided .

由于摩擦会导致切下的毛坯残留在模块里，所以必须在顶出时提供一个向上的冲力。

Kaka then got a low drive away which the 'keeper saved and Rui Costa arrived at the back post only to put a downward header wide.

卡卡随即低射攻门，门将奋力化解。鲁伊。科斯塔又在后门柱头球，可他顶出的弹地球偏了出去。

On the road , when the wheel got stuck in some mud he jumped into the swamp to push the cart out with his shoulder .

在路上他跳进沼泽，用肩膀顶出了陷在泥里的车轮。

one stripper is composed of a knockout pin, the guide column and a knockout pin push plate .

脱模器由顶出针、导柱、顶针推板、复位弹簧组成。

A knockout assembly consists of a plate , a push rod , and a retaining collar .

顶出的安装部件包括一个金属板，推杆，定位圈。

The creation of an excessively high tip supported only by a silicone implant inevitably leads to implant extrusion.

另外，过分的依靠假体支撑来获得高鼻尖只会增加假体的顶出率。

The mainframe includes the body of machine, main cylinder and press edge fitting, and cylinder of pack out and filling liquid equipment etc.

主机部分包括机身、主缸、压边装置、顶出缸及充液装置等组成。

Near the upper limit of the ram stroke, a knockout bar in the press will contact the push rod and eject the blank .

接近限制冲力最高点时，压力推动下的脱模杆会与推杆接触并将毛坯顶出。

The construction here refers to a new kind of air pumping press, realizing the automatic draw, turn over, push out and removal of the mould .

介绍了一种新型抽真空平板硫化机的结构特点。此机器能实现模具的自动推出、开模、翻转、顶出。

Finally , the remaining material head in front from the top of the lathe chuck, no materials folder .

最后所剩下的料头，是从车床夹头前方顶出，不需要料夹。

Assembly organizations from push plate, push the semi-fixed panels and ejector rod composed of injection molding machines .

装配机构由推板、推半固定板和注塑机顶出杆组成。

The exercising member closes the lid and exercises the hinge during travel from the molding position to the ejection position .

所述运用部件在从所述模制位置行进到所述顶出位置期间关闭所述盖子并运用所述铰链。

Further movement of the moving mould plate actuates the stripper plate and the moulding is ejected .

动模板进一步的运动带动推板，使得塑件顶出。

Adjustabel ejection device can be applied to any kinds of products .

可调式顶出装置，更适应于不同高度的产品。

If needed , a large soft top can be swerved all the way back to the C column .

如果需要，一个大的柔软的可以顶出所有的道路都回归 C 柱。

Unfortunately, the square runner is not very satisfactory either, but for another reason : it is difficult to eject .

可是，方形的流道由于另一个原因，也不能另人满意：就是顶出困难。

A large soft top can be swerved all the way back to the C column if needed .

一个大的柔软的可以顶出所有的道路都回归 C 柱如果需要。

drawstring time delay , high-pressure time time, push-out time time, times of push-out, next page, return back .

拉带延时，高压延时，顶出延时，顶出次数，下一页，返回。

Has ordinary push out and heats up push out two modes, the temperature can be set, print a test qualified marks .

分冷顶出和加热顶出，温度可设定，打印测试合格标记。

Dies will be constructed with provisions for positive stripping and ejections of the finished part and all generated scrap .

模具应该构造成能够从正面剥落及顶出成品及废料。

During stage one, the moulding and attached peg are ejected by the ejector pins as shown at 'b'.

在第一阶段，塑件和附加的柱销被顶杆顶出，图 “b ”。

board The first paragraph ejection complete shown in FIG . 4 . (3 ) complete open mold cycle.

第一段顶出完成，如图 4 所示。（3 ）开模周期完成。

Product should be knocked out after mold opened .

开模完成后，产品必须顶出的过程。

顶出

顶出