大家在查：叶叶顺顺利 limitary bricklaying preliminary sketches job sheet OLPW 手术效果判决结果 toxoplasmosis

给料

n.feeding
v.feed
网络feedstock; input; kipliau

给料

英-汉网络释义

给料

v. n.

1.feed

1

The system comprises at least one volumetric dosing unit for metering a volume of the components.

所述系统包括用于计量一定体积组分的至少一个体积定量给料装置。

2

Facing to the general trouble and blemish of the feeding system and combining with produce practice , we carried on structure improvement .

针对均匀给料系统经常易出现的故障和缺陷，结合生产实际，进行了结构改进。

3

After the installation around the feeder should be left not less than 20 mm of travel clearance so that the feeder is completely free state .

安装后的给料机周围应留有不小于 20 毫米的游动间隙，使给料机完全处于自由状态。

4

They are specially used in the industry of the water and electricity, the industry of construction material, the industry of gold ore, etc.

特别适用于水电行业、建筑石英料、金属矿石等粗碎前的给料用。

5

6

In the upper primary crushing stage the feed material is pre-crushed between a crushing plate and a crushing roll .

在位于上方的破碎阶段，给料在破碎板条和一个轧辊之间被破碎。

7

Under the same size fed to a hydrocyclone , the desired overflow size distribution can be obtained by regulating the cut size.

当旋流器给料细度一定时，通过控制分离粒度可以获得所需的溢流细度。

8

Secondary crushing is carried out in the lower section between the rotor and the grinding wall .

在转子和磨碎壁之间的下半部区间，给料被进一步地破碎。

11

14

The feed material is broken between the counter- rotating rolls and crushed by pressure and shearing stress .

在压力和切力的作用下，给料在彼此相向旋转的轧辊间破碎。

15

Senor switches are located near the end of each feed belts .

各传感器开关位于每条给料皮带的末端附近。

16

The weigh belt feeder is designed for quantitative feeding of the bulk materials , the feeding process is continuous with belt .

称重给料机用于对散状物料的定量给料，给料过程为皮带连续给料。

17

Test runs determine the crushing behaviour of your specific feed material .

您们给料的性能在破碎机里被分析。

18

Xs . the main parts is : The wet sand feeder , The elevator , Burner, Dry roller, Dry sand vibration, Bag filter, The cyclone.

它主要由湿砂给料机、斗提机、干燥滚筒、除尘器、燃烧器、筛分机等部件组成。

20

Screw feeders has the feature of the material equably and is convenient to control the feeder capacity.

排料均匀，可以方便地进行调控其给料的特点。

21

WOODWORKING MACHINES . VENEER PRESSES HAND-LOADING . NOMENCLATURE.

木材加工机械 .手工给料贴板机 .术语

23

The feed material is distributed over the whole width of the roll via conveying belts.

输送槽把给料均匀地分布在轧辊的整个宽面。

24

Your feed and feeder Division of the Department of your material compared to pay attention to the taper inentification tension and inertia .

播料部和给料部比拟，播料部给夺目锥度压辛和惯性赔偿不不差错。

25

Improvement measures are suggested on the basis of the comparison of several under bin feeding devices .

对几种仓底给料装置进行了比较，并提出了改进措施。

26

The following detailed say a few words from the feed axis to feed the tension between traction roll control .

底下略说一下从给料轴到给料牵引辊之间的压辛把持息法。

27

Flow flux of feed, the ratio of overflow and underflow are main processing parameters influence the performance of equipment .

给料量、底流和溢流分配比例是影响设备性能的主要工艺参数。

29

Nevertheless , if drop-in fuels are to become a truly big business they need a wider range of feedstocks.

然而，假如 dropin 燃料想成为一个真正意义上的大买卖，它们就需要有更多的可选择的给料。

热词推荐

大家在看