大家在查： attend board 5一费德南比价 Jujube 脑满肠肥 lower limb 不可思议地柔情蜜丝·德

容差

na.allowance; 【机】tolerance; alw
网络Tolerance; Tolerances; Error Tolerance

容差

英-汉网络释义

容差

na.

1.【机】tolerance; allowance; alw

1

Compliance with the tolerances and the requirements for the general condition lies within the responsibility of the manufacturer .

一般条件的容差和要求的符合性在制造商的责任中列出。

2

D. Able to understand and apply Geometric dimensioning and tolerancing (GD&T) at intermediate to expert level preferred .

能理解并应用几何定尺寸定容差（GD&T ）有中高级水平者优先。

3

In what follows, the concept of uncertainty of measurement is introduced first and then the significance of tolerance discussed .

首先介绍了测量的不确定度概念，然后讨论容差的意义。

4

This represents a 'safety margin ' of 5000 flats a year , or 6 per cent of the current forecast of housing demand .

这个数字包括了每年多出 5000 个单位的 “容差 ”量，即较目前预计的房屋需求量多出 6%。

5

For enclosures of light alloys , the percentage content (and tolerance ) of aluminium , titanium and magnesium will normally be required.

轻质合金外壳中铝，钛，镁含量（带容差）

7

For acceptance controls, the dimensions and tolerances specified in these drawings shall be taken into consideration .

对于验收检验，应考虑这些制图中固定的尺寸和容差。

9

Make sure that the Tolerance value is set to about 20 and that the Anti-alias and Contiguous options are checked as demonstrated below.

确保容差设在 20 左右，消除锯齿和连续是勾选上的，如下图

11

12

The bank's inflation target is 3 percent , though that includes what it calls a "tolerance range" of plus or minus 1 percentage point.

银行的通货膨胀目标是百分之 3 ，虽然其包含称为一个正或负 1百分点的 “容差范围 ”。

13

On the basis of SOFM neural network, a new fuzzy diagnosis method for tolerance analog circuits fault is proposed .

提出了基于 SOFM 神经网络的容差模拟电路故障模糊诊断方法及其实现。

15

An algorithm for completing the incomplete data table based on a novel harmonized valued tolerance relation is proposed in this paper.

提出一种基于新型协调量化容差关系的不完备数据补齐算法。

16

Throclgh loss function calculating the allowance , the standard tolerances of hole and shaft are defined.

以损失函数计算孔和轴的工厂容差，选定其标准公差。

17

The fault tolerance can be adjusted .

其中，容差范围可以调整。

18

The interval parameter back analysis program is developed based on the flexible tolerance method .

基于可变容差优化反分析法，开发了区间优化反分析程序。

19

If the collected value was outside the tolerable range , a rule would "fire . "

如果收集到的值超出了容差范围，就会 “激发 ”某条规则。

21

however, it may cause inferior quality . Therefore , it is necessary to study tolerance, and to make trade-off between quality and costs .

因此，有必要对容差进行研究，使产品质量和成本在一定程度能够兼顾。

22

A Study of Optimization on Accessible Nodes in a Tolerance Network

容差网络可及点优化方法的研究

23

The Research of Tolerance Analysis and Its Application of Reliability in ELectronic Circuit

电子线路可靠性容差分析方法及其应用的研究

25

Analysis for measurement reliability and maximum permissible error of measuring equipment

测试设备的测量可靠性及容差分析

26

Criterion modification of tolerance design by considering the quality distribution

考虑质量分布的容差设计准则修正

29

Concurrent Optimization of Parameter Design and Tolerance Design for Multiple Responses

多质量特性产品的参数与容差并行设计优化

30

热词推荐

大家在看