大家在查：产儿 copy document 四面包围争取取得 damsels 证发放 POSIX 西弗勒斯审计员 Downing

公差

na.tolerance; allowance
网络tolerances; common difference; TOL

公差

英-汉英-英网络释义

公差

tolerances

· 公差 (Tolerances) - 这些是与公差格式相关的参数。当尺寸由数字的转向符号的时候出项这些符号。

common difference

英语词汇-数学词汇_专业词汇 ... common denominator 同分母；公分母 common difference 公差 common divisor 公约数；公约 ...

TOL

SSCP缩写的意思-DNA单链构象多态性_英文缩写查询 ... EMS 电子显微镜 TOL 公差 ETDRS 试验型跟踪与数据中继卫星 ...

Size Tolerance

金属材料行业术语 ... 抗化学品能力 Chemical Resistance 公差 Size Tolerance 焊接能力 Weldability ...

allowance

矿业英语 - 豆丁网 ... allowable stress 容许应力 allowance 公差 alloy 合金 ...

Tolerancing

此系列功能可以用来标注各种公差(Tolerancing)符号。 4.3.1 Datum Feature(特征基准) 可以用来标示公差之基准面与基准线。

GD&T

　　PMI 能够包含行为公差(GD&T)、焊缝符号、文本和尺寸，以及产品定义和过程注释。PMI 能够以信息在二维图纸上存在的同样 …

例句：

The statistical tolerance symbol may be applied to a dimensional tolerance or to the tolerance value of a geometric control .

统计公差符号适用于尺寸公差或一个形位公差控制的公差值。

Must be able to understand Geometric tolerancing and dimensioning .

须了解几何公差和规格尺寸。

Optimal dimensional and geometric tolerances could be obtained by an appropriate optimization algorithm for the model .

求解该模型能同时得到优化的尺寸公差和形位公差。

At least one-tenth of the tolerance range of the characteristic to be read directly.

至少需可直接讀到特性規格中公差範圍的十分之一

problems since tolerances decrease down to the range of the surface roughness .

问题，因为减少到公差范围内的表面粗糙度。

It is safer to test whether the absolute value of the difference between the two numbers is less than a small acceptable tolerance .

更好的方法是测试一下两个数之差的绝对值是否小于一个小的可接受公差。

Well, in fact I usually work overtime . And for business trip , it doesn't matter if it is no more than three times a month .

恩，实际上我经常加班。至于出公差，只要每个月不超过 3 次就没关系。

If a minimum diameter is specified the tolerance shall be the total tolerance given in table 8 all over the minimum diameter .

如果指定了最大直径，公差应是表 8 中给出的总公差，所有的都低于最大直径。

The old saw, "a change is as good as a rest " must have been said by a Virgo because Virgos feel better after any trip , even business trips.

有句话这么说滴，“换换环境犹如短暂的休息 ”，说这句话的一定是个处女座的因为处女们在短途旅行后，甚至是出公差后，会感觉好些。

The running accuracy is always at least to tolerance class P6.

运行精度始终符合至少公差级 P6 。

Numerical results showed that on this assumed condition , the smaller the tolerance of roundness is, the longer the fatigue life of hole.

数值模拟结果表明，在此假定条件下，孔的圆度公差越小，孔的疲劳寿命越大；

Flatness tolerance easy to control .

容易控制平面度公差。

Semi-finished products made of magnesium alloys . U-sections . Tolerances on dimensions and recommended dimensions.

镁合金制半成品 .U 形型材 .尺寸公差和推荐尺寸

Be able to read engineering prints and understand tolerance requirement.

能阅读工程图并能理解形位公差。

NON-ROTATING STEM Non-rotating stem has close roundness and straightness tolerances and is burnished for a superior finish .

不旋转阀杆不旋转阀杆具有精密的圆度和平直度公差，并且经过抛光达到极高的抛光度。

semi - finished products made of metal or non - ferrous alloys . titanium sheet , dimensions and tolerances.

金属或有色合金半成品。钛板材。尺寸和公差。

As a general rule, piping flanges should be concentric to pump nozzles to within the flange bolt hole clearance tolerance .

管路法兰与泵口要同心，偏差不能超过法兰螺栓孔尺寸公差。

He's out on official business . 24 . Don't forget to tell him I called.

他出公差去了 .24 .别忘了告诉他，我打过电话来。

a tolerance is the total reliable variation in the size of a part .

公差是零件尺寸的总允许的偏差；

公差

公差