大家在查：问底 FileSecurity odpp therollofthunder 等多种 rock masses 落果 Ai Qing Simulation Model 奥妮娅·塔维拉

应力强度

n.stress intensity
网络intensity of stress; IFSS; MPa

应力强度

英-汉网络释义

应力强度

1.stress intensity

stress intensity

冶金专业英语词汇(S) ... stress gradient 应力梯度 stress intensity 应力强度 stress intensity factor 应力强度因数 ...

intensity of stress

航海及海运专业词汇英语翻译(I) ... intensity of sound 声强度 intensity of stress 应力强度 intensity of suction 吸入强度 ...

IFSS

... 具有较好的与 Kevlar 49 纤维之介面剪应力强度（IFSS）。

MPa

——炭纤维材(棒材或多股材)的允许拉应力强度(MPa)；　　W——拉断荷载力；　　 θ——预张力；　　A e ——炭纤维材的有效直径；　　K …

stress-strength model

半导体雷射技术 Semiconductor Laser Technology ... strain 应变 423 stress-strength model 应力强度 stripe 条状 71, 353 ...

Stress Strength

强度和应力,Strenth and... ... ) stress intensity 应力强度 ) Stress Strength 应力强度 ) intension-stress 强度应力 ...

Kmax

...化对于腐蚀疲劳裂纹扩展速率的影响成为可能 .当最大应力强度 (Kmax)超过给定材料—溶液组合的特定临界特征值时 ,阴极极 …

SH-SL

这将产生一个更大的应力强度（SH-SL）。这种情况通常出现在埋地管道的受压段当中。

例句：

It is obtained that the SIF increases with the length of the surface crack or the reflective crack enlarging in the asphalt pavement .

得出了含表面裂缝和反射裂缝路面体的应力强度因子均随着裂缝长度的增加逐渐增大。

So, if ultrasonic wave is used to determine SIF, only the first one passing through the front (or rear ) surface of the specimen can be used .

要用超声波确定应力强度因子，只能采用透出试件前（或后）表面的第一个纵波信号。

Presents a method that can be conveniently used to calculate the stress intensity factor for the edge crack of a cold expanded hole .

对于残余应力场已知的冷胀孔，用本文方法求孔单边穿透裂纹的应力强度因子是简单和准确的。

An analytical solution for the mode I stress intensity factor at the crack tip of a symmetric parabolic crack is thus obtained .

得到了含轴对称抛物线曲裂纹平面弹性问题的曲裂纹尖端 I 型应力强度因子的解析表达式。

The boundary integral method is applied to the analysis of opening displacement and stress intensity factor of surface crack .

用边界积分方法，分析表面裂纹的张开位移和应力强度因子。

Also, the extrapolation method is used to obtain the SIF and stress triaxiality around the tip cracks.

应用外推法得到应力强度因子及裂尖周围的应力三维度。

The relatively small reduction in stress intensity magnification factor with increasing stiffness of the stiffener .

随着加强肋刚度的增加，应力强度放大因子则相应有所减小。

Their results showed a more rapid rate of increase in the dynamic SIF for blunt than for sharp notches .

它们的结果表明：钝切口比尖锐切口的动态应力强度因子增长率更快。

Analytical solution to stresses, displacements and dynamic stress intensity factors were obtained by the method of self-similar functions .

利用自相似函数的方法获得应力、位移和动态应力强度因子的解析解。

The stress intensity factors of both orthotropic and isotropic materials can be obtained from the present results.

正交各向异性和各向同性材料的应力强度因子均为本文的特例。

The influence of viscosity , Young's modulus ratios , crack lengths were considered. Moreover, some beneficial conclusions were obtained.

分析了粘性，弹模比和缝长对动态应力强度因子的影响，得出了一些有益的结论。

The selection of the service conditions and the allowable stress intensities provides a margin of safety against failure .

服务条件和安全应力强度的选择提供安全范围反对失败。

Moreover, the influences of varied cooling rate and amplitude on the stress intensity factor (DSIF) of crack tip are also discussed .

又探讨不同降温速度，降温幅度对裂纹尖端应力强度因子的影响。

The theoretical equations for stress fields and the stress intensity factor have been derived.

推出了界面裂纹的应力场和应力强度因子的理论表达式。

The analytic solutions of the stress intensity factors at the crack tip are obtained.

分别求得了裂纹尖端应力强度因子的解析解。

The stress concentration factor of the gun tube pit was defined. The FEM models of the pits were built by MSC .

探索出一种估算压坑中最大应力强度的方法：定义了压坑应力集中系数，通过 MSC 。

The main job is to find the stress intensity factors for crack configurations .

其主要任务是确定构型裂纹尖端的应力强度因子。

The stress intensity factor of specimens with different size fracture was calculated .

并且计算了不同尺寸断裂试件的应力强度因子。

The stress -intensity factor corresponding to the arrest of the crack is KISCC as mentioned previously .

如前所述，与裂纹延滞相应的应力强度因子便是 KISCC 。

Then stress intensity factors from the same beams with different ratio of slit and depth are discussed by using software .

同时采用软件对同尺寸不同缝深比下的应力强度因子进行了初步探讨。

应力强度

应力强度

stress intensity

intensity of stress

IFSS

MPa

stress-strength model

Stress Strength

Kmax

SH-SL

热词推荐

大家在看