大家在查： duck egg 找出精确性聋持续增长 accelerations H4 全聋 lieth agog 坚持称

配电板

n.switchboard; distribution panel
网络electrical panel.; switch board; distribution board

配电板

英-汉网络释义

配电板

electrical panel.

模具英文词汇 - MBA智库文档 ... lock washer 锁紧[止动, 防松]垫圈 electrical panel. 配电板,配电盘 nipple 螺纹接头 ...

switch board

航海及海运专业词汇英语翻译(S) ... switch blade 闸刀 switch board 配电板 switch board 配电盘 ...

distribution board

建筑专业英语词汇(D)|房地产建筑专业英语词汇 ... distribution 配置 distribution board 配电板 distribution box 配电箱 ...

distribution panel

航海及海运专业英语词汇(D5) ... distribution packaging 销售包装 distribution panel 配电板 distribution panel 配电盘 ...

power board

压铸英语 - 萍碎无垠的日志 - 网易博客 ... Control panel 控制面板 Power board 分配板, 配电板 Overhauling 大修, 拆修 ...

distributing board

进出口行业词汇英语翻译(D) ... distributing amplifier 分配放大器 distributing board 配电板 distributing box 配电箱 ...

power distribution board

航海及海运专业术语P(5) ... power dissipation 功率耗散 power distribution board 配电板 power distribution box 功率分配箱 ...

distribution switchboard

分配板... ... ) distribution plate 分布板，分配板 ) distribution switchboard 配电板;分配盘 ) distribution panel 分配控制板 ...

例句：

In the next step , you place a mate constraint between the top face of the panel part and the inside back face of the box part .

在下一步中，将在配电板零件顶面和盒子零件的内背面之间置入贴合约束。

Do not attempt to place the panel within the box .

请勿尝试将配电板置入盒子内。

Click anywhere in the blank space around the existing box part to place one occurrence of the panel .

按一下既有盒子零件周围空白空间的任何位置，以置入配电板的一个复本。

Please look at the readings of voltage and frequency on the main switchboard to see if they are normal .

请你看看主配电板上电压、频率的数值是准确。

It's not suitable for these spare parts to be placed here . Please remove them to the rear of the switchboard .

这些备件放在这里是不合适的，请移到配电板后面去。

Locking test between the main switchboard and emergency switchboard .

主配电板与应急配电板自检联锁试验。

Set the switches on MSB to 'Auto' position . Generator is to be tested under no load .

将主配电板上开关设定在自动位置，试验机组没有负载进行。

In the graphics window, select the YZ plane of the panel (click the following image to watch an animation of this selection ).

在图形视窗中，选取配电板的 YZ 平面（按一下下面的影像以观看该选取的动画）。

B. The instruments on the MSB and ESB may be used for measured at test .

主配电板和应急配电板上的仪表，在试验中可作测量用。

After you click , notice that another occurrence of the panel is attached to the cursor and ready for placement .

按一下之后，请注意，会将配电板的另一个复本关联至游标并可以进行置入。

Finally , you constrain the cover part to the box . This process is nearly identical to the steps you took to constrain the panel part .

最后，将盖零件约束至盒子。该程序与约束配电板零件所采取的步骤大致相同。

To finalize the constraint , click Apply . The mate constraint is created and the panel is offset one inch from the back of the box .

若要最终完成约束，请按一下「套用」。将建立贴合约束，并且配电板将相对于盒子背面偏移一英吋。

Click in the following image to watch the animation and then select the face of the panel , as shown .

按一下下面的影像以观看动画，然后选取配电板的面（如图所示）。

Since you only need one occurrence of the panel , press Esc to end the Place operation .

由于您仅需要配电板的一个复本，因此请按 Esc 键结束置入作业。

In this next selection set, you select the XZ plane of the assembly and the XZ plane of the panel .

在下一个选集中，选取组合的 XZ 平面和配电板的 XZ 平面。

Next , you add the panel and cover parts you created in the first two tutorials to the assembly .

接下来，将在前两个自学课程中建立的配电板和盖零件加入至组合。

What can the main switchboards control ?

主配电板能控制什么？

The panel needs one more constraint to finalize its position .

配电板还需要另外一个约束才能最终确定其位置。

could you switch on and start the motor on the MSB after close the cover ?

盖上盖子在主配电板上合上开关并启动电动机？

The panel is attached to your cursor .

将配电板关联至您的游标。

Please show me the main switchboard .

请出示主配电板。

Please tell me the functions of the meters and switches on the board .

请把配电板上的开关仪表的作用介绍一下。

I still have some questions about the switchboard I took yesterday .

关于昨天我接收的配电板我仍然有一些问题。

热词推荐

大家在看

man , . cum you 's " after ? japan : - Facebook what join Yeah your then 4th as