大家在查： redraws 立冬 DeAbrew Urey Hanjiang dressupincostumes former wives marched into 奶牛生气 NortheasternUniversityGraduateSchoolofBu

烧损

na.scaling loss; sparkwear
网络burning loss; fire waste; burn-out

烧损

英-汉网络释义

烧损

burning loss

消防专业词汇英语翻译(A-C) -亿城英语 ... burning life 燃烧寿命 burning loss 烧损 burning mechanism 燃烧机理 ...

fire waste

消防英语专业词汇(F2) ... fire warning 火警 fire waste 烧损 fire watch miner 矿工兼安全检查员 ...

burn-out

电路保护保险丝、烧损(burn-out)电路系统综合型式G-0110N G-0120N G-0130N G-9130 G-0160N G-0210N G-0210NS G-0215N

burn－off

毛面，毛刺，焊瘤 ... burn－in screen 高温功率老化筛选 burn－off 燃尽，烧掉，烧损 burn－off rate 燃尽率 ...

melting loss

熔损,melting... ... ) melting loss 熔损 ) melting loss 烧损，熔损 ) smelting of the burning-loss 熔炼烧损 ...

scaling loss

English-Chinese & World Refractories... ... scaling 脱层，剥落 scaling loss 烧损 scanning 扫描；检测 ...

例句：

Wear and tear to be prevented as well as damage, ingress of grit and dirt, water and oil, paint over spray, burning damages etc.

防止诸如破损、进入灰尘和污泥、水、油、油漆飞溅、烧损等损耗和危害。

Contact burning is one of the main faults of transformer on-load tap changers (OLTC).

触头烧损是电力变压器分接开关主要故障之一。

A new method of using the time of last inflection of burning curve of mold powder as the index of the melting speed is developed .

提出了以保护渣烧损曲线最后一个拐点对应的时间来表征其熔化速度的新方法。

In the heating process of rolling reduction of fuel consumption and ignition loss is of great significance .

轧钢加热过程中，降低燃耗与烧损具有重要意义。

During laser welding of high-strength galvanized steel , the galvanized layer is inevitably lost by having been burned .

激光焊接高强度镀锌钢板时，镀锌层不可避免地遭到烧损。

The oscillating screen motor is frequently overtired, which has great harm to production and economic benefit.

由于振动筛激振电机烧损频繁，严重影响生产及经济效益；

Adopts the fireproof structure . Even if the soft sealing material is burned, the metal seal still takes effect.

采用防火结构，即使软密封材料烧损，金属密封仍能起到作用。

Overloading of axial force acted on working roll is the primary reason to cause the bearing damage .

工作辊轴向力过载是导致轴承烧损的主要原因。

The Kremlin was badly damaged and two thirds of the city was erased.

克里姆林宫的烧损非常严重，三分之二的城市销毁殆尽。

The overburning of electrode and welding gun reduce obviously .

电极与焊枪烧损明显减少。

According to flushing furnace, stabilized BF Gas flow, phenomena of tuyeres damaged were removed .

通过洗炉、稳定煤气流措施使风口频繁烧损现象消除。

It is concluded that calculating exactly the axial load is the key to the settlement of work roll bearing damage .

结果表明：准确计算其轴向力的大小，是解决工作辊轴向烧损的关键。

Under the premises to meet the need of cathode cleaning , it can reduce deterioratqon of tungsten electrode furthest .

在保证阴极清理作用的前提下，可以最大限度地减少钨极的烧损。

In addition , some advice was given on soluting the oxygenated burning loss of liquid aluminium surface and the erosion of crucible .

此外，对解决铝液表面氧化烧损和坩埚内壁腐蚀问题提出了参考意见。

Rerearch on the Question of Seriously Burning Electric Components Ant its Treatment

鹰邵段电气部件严重烧损问题及处理办法的探讨

Analysis of the cause of traction motor burning-out in locomotive at depot and the preventions

到段机车牵引电机烧损原因探析及预防

Welding for the Burned Parts of the Radiation Section of Furnace Tube in Vinyl-Fragmentation Furnace

乙烯裂解炉辐射段炉管烧损部位的焊接

Cause and countermeasure for cycle system of condenser burned out in mechanical heat preservation car

机保车制冷机组循环风机烧损原因与防止对策

Analysis of the burn-out of a high voltage motor and relative solution

浅析造成高压电动机烧损的原因和防范措施

Causes of the pearling and burn-out of locomotive axle suspension bush and preventive measures

机车抱轴瓦碾片、烧损的原因及预防

Discussion on Electrical Grounding Protective Circuit Burn up for Singlemanning Locomotive

单司机值勤机车接地保护电路烧损现象的探讨

Analysis of the trouble of a burnt big end bearing of connecting rod of a marine diesel engine

船舶柴油主机连杆大端轴瓦烧损事故浅析

Causes of Burn-out of the Boiler Burner of the Power Station and the Countermeasures

电站锅炉燃烧器烧损的原因及对策

Damage Reason of the Thrust Face of Sleeve Bearing on Motor Used in the Multi-stage Pump

多级泵电机轴瓦止推面烧损原因分析和对策

Experimental Study of factor influencing on billet oxygenation loss

钢坯氧化烧损影响因素试验研究

Burning Damage Causes of the Bearings of a Diesel Engine and the Countermeasures

柴油机轴承烧损原因及其对策

热词推荐

大家在看

man , . cum you 's " after ? japan : - Facebook what join Yeah your then 4th as